1527
11/8/2015 12:00:00 AM

ASME INTERNATIONAL

ASME is a not-for-profit membership organization that enables collaboration, knowledge sharing, career enrichment, and skills development across all engineering disciplines, toward a goal of helping the global engineering community develop solutions to benefit lives and livelihoods. Founded in 1880 by a small group of leading industrialists, ASME has grown through the decades to include more than 130,000 members in 158 countries.

Standards

Search:

Pump system energy assessment

this international standard sets the requirements for conducting and reporting the results of a pumping system energy assessment (hereafter referenced as "assessment") that considers the entire pumping system, from energy inputs to the work performed as the result of these inputs. the objective of a pumping system energy assessment is to determine the current energy consumption of an existing system and identify ways to improve system efficiency. these requirements consist of — organizing and conducting an assessment, — analysing the data from the assessment, and — reporting and documenting assessment findings. this international standard is designed to be applied, to open and closed loop pumping systems typically used at industrial, institutional, commercial, and municipal facilities, when requested. this international standard is focused on assessing electrically-driven pumping systems, which are dominant in most facilities, but is applicable with other types of drivers, such as steam turbines and engines, and drives such as belt. the international standard does not a) specify how to design a pumping system, b) give detailed qualifications and expertise required of the person using the international standard although provides a list of body of knowledge in annex c, c) address the training or certification of persons, d) specify how to implement the recommendations developed during the assessment, but does include requirements for an action plan, e) specify how to measure and validate the energy savings that result from implementing assessment recommendations, f) specify how to make measurements and how to calibrate test equipment used during the assessment, g) specify how to estimate the implementation cost or conduct financial analysis for recommendations developed during the assessment, h) specify specific steps required for safe operation of equipment during the assessment. the facility personnel in charge of normal operation of the equipment are responsible for ensuring that it is operated safely during the data collection phase of the assessment, i) address issues of intellectual property, security, confidentiality, and safety.

80000 ریال

Metric Hex Jam Nuts

20000 ریال

Powered Industrial Trucks: Symbols for Operator Controls and Other Displays Identical to ISO 3287:1999; Replaces ASME B56.11.3

This Standard establishes symbols for use on operator controls and other displays on powered industrial trucks.

10000 ریال

Gas Turbines: Procurement Part 1: General Introdustion and Definitions ISO 3977-1:1997; Supersedes B133.2-1997

This Part of ASME 3977 groups together the terms and definitions given in ISO 11086 that are relevant to the procurement of gas turbine systems, and defines additional terms.

10000 ریال

Gas Turbines: Procurement Part 2: Standard Reference Conditions and Ratings ISO 3977-2: 1997; Supersedes B133.6-1978

This Part of ASME 3977 specifies the standard reference conditions and ISO standard ratings for gas turbines.

10000 ریال

Valves Flanged, Threaded, and Welding End

<div><font face=Arial>This code or standard was developed under procedures accredited as meeting the criteria for American National</font></div> <div><font face=Arial>Standards. The Standards Committee that approved the code or standard was balanced to assure that individuals from</font></div> <div><font face=Arial>competent and concerned interests have had an opportunity to participate. The proposed code or standard was made</font></div> <div><font face=Arial>available for public review and comment that provides an opportunity for additional public input from industry, academia,</font></div> <div><font face=Arial>regulatory agencies, and the public-at-large.</font></div> <div><font face=Arial>ASMEdoes not &quot;approve,&quot; &quot;rate,&quot; or &quot;endorse&quot; any item, construction, proprietary device, or activity.</font></div> <div><font face=Arial>ASME does not take any position with respect to the validity of any patent rights asserted in connection with any</font></div> <div><font face=Arial>items mentioned in this document, and does not undertake to insure anyone utilizing a standard against liability for</font></div> <div><font face=Arial>infringement of any applicable letters patent, nor assume any such liability. Users of a ctJde or standard are expressly</font></div> <div><font face=Arial>advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, is</font></div> <div><font face=Arial>entirely their own responsibility.</font></div> <div><font face=Arial>Participation by federal agency representative(s) or person(s) affiliated with industry is not to be interpreted as</font></div> <div><font face=Arial>government or industry endorsement of this code or standard.</font></div> <div><font face=Arial>ASMEaccepts responsibility for only those interpretations of this document issued in accordance with the established</font></div> <div><font face=Arial>ASMEprocedures and policies, which precludes the issuance of interpretations by individuals.</font></div>

10000 ریال

Air Gaps in Plumbing Systems R(2002)

10000 ریال

Air Gap Fittings for Use with Plumbing Fixtures, Appliances, and Appurtenances

This Standard establishes physical requirements and methods of testing for air gap fittings for protecting against back siphonage and back pressure backflow.

10000 ریال

Anti-siphon fill valves for water closet tanks

this standard covers anti-siphon fill valves intended to be installed in water closet tanks. note: in this standard, anti-siphon fill valves are also referred to as "devices". in this standard, "shall" is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; "should" is used to express a recommendation or that which is advised but not required; and "may" is used to express an option or that which is permissible within the limits of the standard. notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. notes to tables and figures are considered part of the table or figure and may be written as requirements. annexes are designated normative (mandatory) or informative (non-mandatory) to define their application. si units are the units of record in canada. in this standard the inch/pound units are shown in parentheses. the values stated in each measurement system are equivalent in application; however, each system is to be used independently. combining values from the two measurement systems can result in non-conformance with this standard. all references to gallons are to u.s. gallons. &nbsp;

80000 ریال

Performance requirements for water temperature limiting devices

this standard covers water temperature limiting devices intended to limit the hot or tempered water temperature supplied to fittings for fixtures such as sinks, bidets, lavatories, and bathtubs to reduce the risk of scalding. these devices are not designed to address thermal shock. note: unless otherwise specified in this standard, water temperature limiting devices are referred to as “devices”. in this standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the standard. notes accompanying sections do not include requirements or alternative requirements; the purpose of a note accompanying a section is to separate from the text explanatory or informative material. notes to tables and figures are considered part of the table or figure and may be written as requirements. annexes are designated normative (mandatory) or informative (non-mandatory) to define their application. si units are the units of record in canada. in this standard, the inch/pound units are shown in parentheses. the values stated in each measurement system are equivalent in application; however, each system is to be used independently. combining values from the two measurement systems can result in non-conformance with this standard. all references to gallons are to u.s. gallons. for information on the conversion criteria used in this standard, see annex a.

80000 ریال

Backwater Valves R(1998)

Development of adequate standards covering design, quality and performance of serving check backwater valves for use in building drainage systems. This standard covers: a. Definitions b. Nomenclature and Types c. Connectionsd.d. Materials and Finishes e.

10000 ریال

Grease Interceptors

This Standard covers general product requirements as well as the performance criteria for the testing and rating of grease interceptors, whose rated flows are 100 gpm (380 L/m) or less.

10000 ریال

Grease Removal Devices

This Standard establishes requirements for grease interceptors that are equipped with automatic grease removal devices (GRD). It includes testing requirements and performance criteria designed to ensure conformance to this Standard. Such devices are desig

10000 ریال

Plumbing supply fittings

20000 ریال

Plumbing Fixture Fittings

This Standard establishes general performance requirements and test methods for plumbing fixture fittings, other terminal fittings, supply stops, wastes, and traps. It does not apply to conventional fittings such as nipples, elbows, tees, etc.

10000 ریال

Plumbing waste fittings

this standard covers plumbing waste fittings of sizes nps-2 and smaller. this standard does not cover (a) plumbing supply fittings, which are covered by asme a112.18.1/csa b125.1; (b) other devices (e.g., temperature-actuated in-line mixing valves), which are covered by csa b125.3 or other plumbing product standards; and (c) flexible water connectors under continuous pressure, which are covered by asme a112.18.6/ csa b125.6. this standard does not cover pipes and tubes or pipe and tube fittings that are downstream of the trap. in this standard, "shall" is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; "should" is used to express a recommendation or that which is advised but not required; and "may" is used to express an option or that which is permissible within the limits of the standard. notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. notes to tables and figures are considered part of the table or figure and may be written as requirements. annexes are designated normative (mandatory) or informative (nonmandatory) to define their application. si units are the units of record in canada. in this standard, the inch/pound units are shown in parentheses. the values stated in each measurement system are equivalent in application; however, each system is to be used independently. combining values from the two measurement systems can result in non-conformance with this standard. all references to gallons are to u.s. gallons. for information on the conversion criteria used in this standard, see annex a. &nbsp;

80000 ریال

Plumbing Fixture Waste Fittings

This Standard establishes performance requirements and test methods for plumbing fixture waste fittings such as, but not limited to: bathtub waste and overflow drains; traps; trap wall adapters; fixture strainers and drains; pop-up assemblies; continuous

10000 ریال

Plumbing waste fittings

20000 ریال

Performance Requirements for Backflow Protection Devices and Systems in Plumbing Fixture Fittings

10000 ریال

Flexible water connectors

20000 ریال
نمایش از 1 تا 20 در 1527 استاندارد(76 صفحه)